In this section please find general information on our products:
Colour
The colours depicted on this website are as accurate as modern photography allows. Tonal variations are evident in all Bradstones manufactured and natural stone products, we therefore recommend that colours are judged from actual materials. This is of significant importance when selecting a natural stone product, where, by nature, each component will exhibit considerable deviations. It is important to view a range of samples at a stockist to acknowledge the authentic diversity in colours, textures and markings.
Bradstone’s manufactured products are designed to simulate natural stone and naturally occurring aggregates are utilised, therefore variation between batches can occur. Where possible, products should be selected from the same production batch.
Reconstituted stone will weather in a similar way to natural stone, therefore the effect of the elements and site conditions may cause some colour change dependant on the degree of exposure.
Being a natural stone product means that no two stones are the same and can result in a wonderfully random riot of colour bringing a unique look to your garden. After laying, some natural stone products may exhibit a brown colouration where oxidation of any iron content occurs.
Patio maintenance
Regular maintenance is required to keep the overall appearance of the product in pristine condition. We recommend thoroughly washing paved areas with warm soapy water and brushing off with a stiff broom three or four times a year.
High pressure washers are not recommended for use on manufactured paving.
Bradstone cannot be held responsible for the possible effects or damage caused by the contamination or application of some chemically based products which come into contact with a concrete surface eg some weed killers and acid or alkaline based cleaners.
To prevent possible surface damage, do not use de-icing substances on the Bradstone range of decorative paving.
Natural stone products
Natural Stone is an extremely hard wearing and low maintenance paving. It may, however, contain minor imperfections and foreign materials as part of its inherent make up. This does not affect the performance of the paving, but may mean that some discolouration occurs naturally, although this can usually be cleaned with proprietary cleaners. All natural sandstone products should be laid on a full mortar bed. Due to the light colour of Polished Natural Sandstone we recommend you seal it.
Cost
Bradstone regrets it is not able to quote recommended retail prices as these are set by its stockists and may be subject to variation. Your local stockist will provide full details of prices in your area. It is worth noting that the cost of paving or walling is rarely the major proportion of a typical garden landscaping budget, particularly if employing a professional landscaper or builder.
Application / suitability
Bradstone’s manufactured products are reconstructed stone and the paving range is primarily intended for domestic landscape use. The manufacturer cannot accept any liability in respect of products being used for any inappropriate purpose.
In the unlikely event of product reaching you in a less than satisfactory condition, please refer to your stockist immediately, allowing time for the rejected product to be replaced. All product must be checked on arrival. If a complaint is raised after laying a product, Bradstone cannot accept resonsibilty for any defect.
Sizes and joint widths
All dimensions quoted on this web site are nominal and are for guidance only. Actual sizes will vary, particularly on the products designed to replicate natural stone which have features such as riven profiles and fettled edges. Where space is critical, we recommend dry laying the product to check area required (especially circles and patio feature kits). The sizes and quantities given in the colours and sizes tables usually allow a nominal 10-15 mm joint width. When laying random paving and circles, joint widths will depend on the paving type and laying pattern chosen and will be variable – from approximately 10mm to 30mm.
Paving dark patches
Sometimes dark patches appear on the surface of concrete paving slabs. It is caused by the movement of the moisture content within the paving slab drying the surface at different rates. Given time and natural weathering the darker patches tend to tone down and become less apparent.
Health and safety
Good manual handling techniques should be adopted when handling products. Some products in the range are heavy or an awkward shape and it is recommended that suitable lifting equiptment is used for these products.
Always wear gloves and safety footwear when handling the product.
If product is being cut, always wear safety goggles, and when using a high speed cutter also wear suitable respiratory protection, such as a dust mask.
Before removing wrapping or banding, ensure that the products are on level ground or retained in some way to prevent falling over. When removing shrink wrapping and banding use the appropriate cutting tools; also it is recommended that safety goggles are worn.
Product should always be handled with care as breakages, chippings and other damage may result from mishandling. Minor scuffing can occur due to movement in transit and will generally dissapear in time.
If in doubt do not lay and consult your stockist.
Please Note
Our policy is one of continued improvement, innovation and development and as such we reserve the right to change specification without notice.